Puerto Rico Classic Bimmer Group
¿Quieres reaccionar a este mensaje? Regístrate en el foro con unos pocos clics o inicia sesión para continuar.

Especificaciones del Motor 2.3L para los S14 E30 M3

Ir abajo

Especificaciones del Motor 2.3L para los S14 E30 M3 Empty Especificaciones del Motor 2.3L para los S14 E30 M3

Mensaje  BMWS14M3 Dom Dic 20, 2009 8:02 pm

Esto ayuda mucho cuando vas a realizar un rebuild del motor y quieres mantenerlo OEM 2.3L


S14 ENGINE REBUILDING SPECIFICATIONS CHART

Cylinder block

Cylinder bore

Standard size: 3.6771-3.6775 in. 93.40-93.41 mm

Intermediate size: 3.6791-3.6795 in. 93.45-93.46 mm

Overbore 1: 3.6850-3.6854 in. 93.60-94.61 mm

Overbore 2: 3.6929-3.6933 in. 93.80-93.81 mm

Maximum out-of-round: 0.0002 in. 0.005 mm

Maximum taper: 0.0004 in. 0.01 mm


Cylinder head


Cylinder head height

New height: 3.7783-3.7707 in. 95.97-96.03 mm

Minimum machined height: not recommended

Valve guide total length: 1.7022-1.718 in. 43.3-43.7 mm

Valve guide head bore diameter

Standard size: 0.4717 in. 12.0 mm

Overbore 1: 0.4796 in. 12.2 mm

Overbore 2: 0.4953 in. 12.4 mm


Valve guide installed inside diameter


Standard size: 0.2756 in. 7.0 mm

Overbore 1: 0.2796 in. 7.1 mm

Overbore 2: 7.2 mm

Valve guide installing temperature

Cylinder head: +300°F + 150°C

Valve guide: – 240°F -150°C.

Valve guide protrusion: 0.5897 in. 15 mm

Valve seat angle: 35/45/60 degrees

Valve seat width

Intake: 0.047-0.051 in. 1.2-1.3 mm

Exhaust: 0.055-0.059 in. 1.4-1.5 mm


Valve seat diameter


Intake: 1.441-1.445 in. 36.6-36.7 mrn

Exhaust: 1.236-1.240 in. 31.4-31.5 mm


Crankshaft


Main bearing diameter

Double classification

Standard size

Red: 2.1649-2.1645 in. 54.990-54.980 mm

Blue: 2.1645-2.1 642 in. 54.980-54.971 mm

Undersize 1

Red: 2.1551-2.1547 in. 54.740-54.730 mm

Blue: 2.1547-2.1543 in. 54.730-54.721 mm

Undersize 2

Red: 2.1452-2.1448 in. 54.490-54.480 mm

Blue: 2.1448-2.1445 in. 54.480-54.471 mm

Undersize 3

Red: 2.1354-2.1350 in. 54.240-54.230 mm

Blue: 2.1350-2.1346 in. 54.230-54.221 mm

Triple classification

Standard size

Yellow: 2.1647-2.1649 in. 54.984-54.990 mm

Green: 2.1644-2.1647 in. 54.977-54.983 mm

White: 2.1642-21644 in. 54.971-54.976 mm

Undersize 1, 0.25mm

Yellow: 2.1549-2.1551 in. 54.734-54.740 mm

Green: 2.1546-2.1548 in. 54.727-54.733 mm

White: 2.1544-2.1546 in. 54.721-54.726 mm



Undersize 2, 0.50mm

Yellow: 2.1450-2.1453 in. 54.484-54.490 mm

Green: 2.1447-2.1450 in. 54.477-54.483 mm

White: 2.1445-2.1447 in. 54.471-2.1447 mm

Undersize 3, 0.75mm

Yellow: 2.1 352-2.1354 in. 54.234-54.240 mm

Green: 2.1349-2.1351 in. 54.227-54.233 mm

White: 2.1347-2.1349 in. 54.221-54.226 mm


Crankshaft main bearing clearance


Double classification: 0.0012-0.0027 in. 0.03-0.07 mm

Triple classification: 0.0008-0.0018 in. 0.020-0.046 mm

Crankshaft thrust bearing ground size

Standard size: 1.1811 in. 30.0 mm

Oversize 1: 1.890 in. 30.2 mm

Oversize 2: 1.1968 in. 30.4 mm

Oversize 3: 1.2047 in. 30.6 mm

Crankshaft end play: 0.0033-0.0068 in. 0.085-0.174 mm

Connecting rod bearing journal ground size

Standard size: 1.8888-1.8894 in. 47.975-47.991 mm

Undersize 1, 0.25rnm: 1.8789-1.8796 in. 47.725-47.741 mm

Undersize 2, 0.50mm: 1.8691-1.8697 in. 47.475-47.491 mm

Undersize 3, 0.75mm: 1.8592-1.8599 in. 47.225-47.241 mm


Connecting rod bearing clearance


Standard classification: 0.0012-0.0027 in. 0.03-0.07 mm

Double classification: 0.0008-0.0022 in. 0.020-0.055 mm

Crankshaft runout at center main: 0.004 in. 0.1 mm


Connecting rods


Bushing diameter

Outside: 0.9449-0.9457 in. 24.000-24.021 mm

Inside: 0.8669-0.8671 in. 22.020-22.024 mm

Maximum weight deviation in engine without bearing shells

Total: ±0.14 oz. ±4g

Big end: ±0.07 oz. ±2g

Small end: ±0.07 ±2g

Big end bore

Red: 2.0427-2.0475 in. 52.000-52.008 mm

Blue: 2.0476-2.0479 in. 52.009-52.016 mm

Standard: 2.0472-2.0476 in. 52.000-52.010 mm


Pistons


Piston diameter-measured 0.236 in. (6.00mm) from bottom of the skirt

Standard size: 3.675 in. 93.35 mm

Intermediate size: 3.677 in. 93.40 mm

Overbore 1: 3.683 in. 93.55 mm

Overbore 2: 3.691 in. 93.75 mm


Piston clearance


New engine: 0.0012-0.0024 in. 0.03-0.06 mm

Used engine: 0.006 in. 0.15 mm


Piston rings


Top compression

End clearance: 0.0118-0.0216 in. 0.30-0.55 mm

Side clearance: 0.0023-0.0035 in. 0.06-0.09 mm


Bottom compression

End clearance: 0.0118-0.0216 in. 0.30-0.55 mm

Side clearance: 0.0023-0.0035 in. 0.06-0.09 mm


Oil control

End clearance: 0.0098-0.0196 in. 0.25-0.50 mm

Side clearance: 0.0007-0.0019 in. 0.02-0.05 mm


Camshaft

End play: 0.004-0.006 in. 0.1-0.15 mm

Bearing clearance: 0.001 1-0.0021 in. 0.027-0.053 mm

Tappet bore diameter: 1.4764-1.4770 in. 37.500-37.516 mm

Tappet bore clearance: 0.001 0-0.0026 in. 0.025-0.066 mm



Valves

Valve lash

Cold: 0.010-0.014 in. 0.26-0.35 mm

Operating temperature: 0.013-0.015 in. 0.34-0.39 mm

Head edge thickness

Intake: 0.020 in. 0.50 mm

Exhaust: 0.037 in. 0.95 mm

Head diameter

Intake: 1.457 in. 37 mm

Exhaust: 1.260 in. 32 mm

Stem diameter

Standard size: 0.275 in. 7.0 mm

Oversize 1: 0.279 in. 7.1 mm

Oversize 2: 0.283 in. 7.2 mm

Stem to guide tilt clearance

Intake: 0.025 in. 0.65 mm

Exhaust: 0.031 in. 0.80 mm


Oil pump

Pressure at idle: 7-28 psi 0.5-2.0 bar

Pressure at top speed: 57-85 psi 4.0-6.0 bar

Pressure relief valve spring length

Operating pressure valve: 2.677 in. 68.0 mm

Bypass pressure valve: 1.732 in. 44 mm

Vibration damper

Radial runout, maximum: 0.012 in. 0.3 mm

Axial runout, maximum: 0.012 in. 0.3 mm
BMWS14M3
BMWS14M3
Chofer
Chofer

Cantidad de envíos : 59
Fecha de inscripción : 09/09/2009
Edad : 45
Localización : San Juan

Volver arriba Ir abajo

Volver arriba

- Temas similares

 
Permisos de este foro:
No puedes responder a temas en este foro.